Jan 29, 2012 Hi, I am using MacBook Pro 13' and Traktor Pro. I would like to pre-listen to the next song with my headphones while listening to the current song with my speakers, but I. It is usually connected physically to a pair of headphones and activated by pressing on the Cue (headphones) button of the corresponding Deck in the software mixer. In the example below, the TRAKTOR KONTROL Z1 audio interface is routed for these two output channels in internal mixing mode.
Hello, I have a Nurmark mixtrack pro + virtual DJ. But I have alot of latency problems. I tried latency settings from auto to 256 (5ms) with and without safe mode. Also I switched from optimized for quality to latency. I use advanced stretching. But nothing seems to work.
Any ideas?
This topic was modified 5 years, 1 month ago by .
Does it improve if you unplug the controller and test it with just mouse/keyboard?
Well … going from auto to 5ms is going the wrong direction if latency is your problem. What you want to do is EXTEND the latency setting to a higher number of ms. Make a big jump higher and if it’s gone, then start babystepping back until it occurs again. You’ll have found the best setting your system can handle.
I am not sure what you mean by stretching, but if it involves lots of processor-heavy audio manipulation, I can imagine you get problems. Since you don’t mention what kind of laptop/computer you are using not much I can say to that end of the equation.
Finally, I do assume you have the latest updated (audio) drivers installed?
On my windows 8.1 laptop, i run VDJ 8 at around 10ms latency through my Focusrite 2i4 with the ASIO drivers for it (at 24bit, 96KHz) – with VDJ set to:
SAMPLE RATE: 96000 LATENCY: “Automatic (288)” ultralatency off overclock on and all the quality settings on max
These may not be the best settings for you, but they work for me.. 🙂
And I can’t find “Advanced Stretching – or anything to do with stretching – anywhere??
If on Windows:
Check your USB drivers – make sure they are up to date, re-install the drivers for your soundcard (whilst it is plugged in) and then only use it on that one USB port – it does matter. And then reset the settings in VDJ.
If you are on a Mac:
Install any relevant Core Audio drivers (if applicable) and reset the settings in VDJ.
If that doesn’t sort it, I don’t know…
And which version of VDJ are on?? I’m on the latest update of 8 🙂
i have a Denon MC3000 controller what version of virtual Dj it work with can you help?
hi guys im having some problem in set up MC3000 with Traktor Pro i can only only listen to one channel on the Headphone what i am doing wrong?
Don’t know too much about audio settings in VDJ, but is sure sounds like something is set wrong there.
Howdy, Jonas – You will get a more positive response by creating your own topic rather than adding unrelated questions to an existing thread. The “new post” thingy is at the bottom of the forum page where you would want to post it. Hope that helps.
@ Fgjghkhlfxl Xfhfgjkgxhk
Virtual Dj 7 try these Sound Card 512(11ms) Safe Mode should be unchecked Optimize for Quality Master Tempo (I chose Purescratch no master tempo) 48Khz Conversion Faster Resampling
Virtual Dj 8 try these Performance Samplerate 41000 latency 512(11ms) ultralatency no overclock no pitchquality 2 scratchfilter 9
Is that sample rate 44100 not 41000 ???
Didn’t know that 41000 was a standard.. 😉
Posts
Change Headphone Settings On Traktor Pro 2
The forum ‘DJing Software’ is closed to new topics and replies.
Open the AirPods Case, then go to Settings > Bluetooth on your iOS or iPadOS device. Tap the information button next to your AirPods in the list of devices. Here's what you can do:
Name your AirPods
Tap the current name. Then enter a new name for your AirPods and tap Done.
Change the press-and-hold action on AirPods Pro
AirPods Pro have three noise control modes: Active Noise Cancellation, Transparency mode, and Off. By default, when you press and hold the force sensor on the stem of your left or right AirPod, your AirPods Pro switch between Active Noise Cancellation and Transparency mode.* You can change which noise control modes the press-and-hold action uses:
Go to the settings screen for your AirPods Pro.
Under Press and Hold AirPods, tap Left or Right, then make sure that Noise Control is selected.
Select the two or three noise control modes that you want to use with press and hold. If both AirPods are set to change noise control modes, a change to the press-and-hold action settings on one AirPod applies to both.
You can also set the press-and-hold action to allow you to use Siri. In the AirPods Pro settings screen, tap Left or Right, then select Siri. You can have one AirPod set for Siri and the other set to change noise control modes.
* You can switch among all three noise control modes in Control Center or Settings.
Change the double-tap action on AirPods
With AirPods (1st and 2nd generation), select the left or right AirPod in the AirPod settings screen and then choose what you want to happen when you double-tap the AirPod:
Use Siri to control your audio content, change the volume, or do anything else Siri can do
Play, pause, or stop your audio content
Skip to the next track
Go back to the previous track
Change Headphone Settings On Traktor Pro 1
Turn Automatic Ear Detection on or off
By default, AirPods sense when they're in your ear and receive the audio from your device. AirPods also pause and resume playback when you remove one of your AirPods, or stop playback—and won't resume—when you remove both. When you have Automatic Ear Detection on and you're not wearing your AirPods, audio plays through your device's speakers.
Change Headphone Settings On Traktor Problems
When you turn off Automatic Ear Detection, these features are off and all audio plays to your AirPods whether or not you're wearing them.
Set Microphone to left, right, or automatic
There's a microphone in each AirPod, so you can make phone calls and use Siri. By default, Microphone is set to Automatic, so that either of your AirPods can act as the microphone. If you're using only one AirPod, that AirPod will be the microphone.
You can also set Microphone to Always Left or Always Right. These set the microphone to either the left or right AirPod. That AirPod will be the microphone even if you remove it from your ear or put it in the case.